Standard disclaimer: Use the information that follows at your own risk. If you screw up a system, don't blame it on me...
Command |
Description |
||||
cb_reset |
Resets and reboots control boards which will reset all active domains. Use this only when the control boards have stopped responding or when you need to change the control boards' IP addresses. |
||||
cb_prom |
Used to update the flash PROM on the control boards. |
||||
domain_create |
Used to create domains |
||||
-d ${domain_name} |
Name of the domain; must also be the domain's hostname |
||||
-b ${sbs[*]} |
List of system boards that will comprise the new domains separated by spaces. |
||||
-o ${os_version} |
The OS version that will be installed on the new domain |
||||
-p ${E10K_name} |
The name of the E10K platform; useful for when your SSP is managing more than one E10K platform. |
||||
domain_history |
Displays the contents of the domain_history file showing which domains have been removed but can be recreated and which system boards compose them. |
||||
domain_remove |
Removes/deactivates domains. Only argument: -d ${domain_name} |
||||
domain_rename |
Renames domain names |
||||
-d ${old_name} |
Old domain name |
||||
-n ${new_name} |
New domain name |
||||
domain_status |
Displays the contents of the domain_config file showing which domains can be activated and which boards are contained within them. |
||||
domain_switch |
An alias that changes the value of the SUNW_HOSTNAME parm and the prompt. |
||||
edd_cmd -x [start|stop] |
Turns on/off edd processing. |
||||
fan |
Displays and controls power and speed settings for fans. |
||||
-l {front|rear} |
Display power speed settings for fans on front/rear of system only. |
||||
-t # # # |
Apply action to selected fan trays only. |
||||
-p {on|off} |
Turn on/off power to selected fan trays. If no -t #, applies action to all fan trays. |
||||
-s { nominal | fast} |
Change the speed setting for selected fan trays. If no -t #, applies a ction to all fan trays. |
||||
hostview |
Provides GUI access to most E10K platform/domain management tasks. |
||||
sys_clock |
|
||||
ssp_config |
|
||||
ssp_unconfig |
|
||||
autoconfig |
|
||||
board_id |
|
||||
redx |
|
Command |
Description |
||||
bringup |
Sets the h/w config, configures the centerplane if needed, runs POST, loads and starts OBP, and starts the netcon_server |
||||
-f |
Don't check to see if domain is already running. Will crash a running domain |
||||
-A {on|off} |
Toggles the auto-boot? OBP parameter. |
||||
-C |
Forces configuration of the centerplane. Any running domains will crash |
||||
-l {7-15} |
Diagnostic level; 7 takes a long time; 15 will take forever. |
||||
check_host |
|
||||
hostinfo |
Provides detailed system status information |
||||
-F |
Provides fan status |
||||
-S |
Provides CPU signature information |
||||
-h |
|||||
-p |
Provides system component power status |
||||
-t |
Provides system temperature information |
||||
hpost |
|
||||
netcontool |
|
||||
power |
Directs the control board to change the system power state: |
||||
-on |
Turns on power |
||||
-all |
Apply power to everything: full cmd: power -on -all |
||||
-off |
Turns off power |
||||
-B |
Turns off power to everything: Full cmd: power -B -off |
||||
-sb [n n# n## ...] |
Apply action to specific system boards |
||||
-s |
Turn on/off selected power supplies |
||||
-p |
Turn on/off specific power distribution units |
||||
sigbcmd |
|
||||
sys_clock |
|
||||
sys_id |
(Re)Creates or checks the domain eeprom.image file. |
||||
-f eeprom.image.${domain_name} |
Resulting output filename |
||||
-k ${key} |
Domain key that SUN provides |
||||
-s ${serial} |
Domain serial number used to create the first domain |
||||
-h ${hostid |
Hostid that SUN provides used to create additional domains |
||||
-d |
Confirms proper eeprom.image file creation |
||||
sys_reset |
|
||||
netcon |
|
||||
hostint |
|
||||
hostreset |
|
||||
drview |
|
||||
netcon_server |
|
||||
dr |
|
||||
init_attach |
|
||||
complete_attach |
|
||||
drain |
|
||||
reconfig |
|